GRC構件是一種裝飾材料，可以以自由的形式滿足設計師各種個性形式的要求，因此受到設計師的青睞，當然，安裝的規格也是必要的，以下小編將教你如何正確安裝
山東GRC構件。
GRC components are decorative materials that can meet the requirements of designers in various personality forms in free forms, so they are favored by designers. Of course, the specifications for installation are also necessary. The following small series will teach you how to correctly install Shandong GRC components.
正確的安裝方法：
Correct installation method:
1.根據圖紙在GRC構件安裝處放出定位線。
1. Set out the positioning line at the GRC component installation position according to the drawing.
2.然后按照施工圖紙的說明安裝切割尺寸的GRC構件，切割GRC構件時，如何掌握GRC構件的尺寸，確保線跡的寬度正好。
2. Then install GRC components with cutting size according to the instructions of the construction drawings. When cutting GRC components, how to master the size of GRC components? First, ensure that the width of the stitches is just.
3.粘貼GRC構件時，網眼布可以折疊，也可以直接粘貼。使用性能良好的粘結砂漿，可用薄層密實的方法將砂漿從GRC構件中強制擠出，粘接處用粘接劑固定，寬度小于3mm，保持粘接處牢固清潔。
3. When pasting GRC components, the mesh cloth can be folded or pasted directly. Use bonding mortar with good performance. The mortar can be forced out of GRC components by thin-layer compaction. The bonding part is fixed with adhesive with a width of less than 3mm. Keep the bonding part firm and clean.
4.安裝山東GRC構件，先測量構件的尺寸，現在試著用平地拼接，構件之間的間隙小于3mm時，用性能良好的粘結砂漿粘結，注意粘結砂漿的均勻分布。
4. When installing Shandong GRC components, measure the size of the components first, and then try to splice them with flat ground. When the gap between components is less than 3mm, use bonding mortar with good performance to bond, and pay attention to the uniform distribution of bonding mortar.
5.檢查拼接好的GRC構件，可用砂紙打磨接縫粘結砂漿。粘結砂漿干燥后，可以使用GRC構件的抗裂橡膠進一步粘結。
5. Check the spliced GRC components and grind the joint bonding mortar with sand paper. After the bonding mortar is dried, the crack resistant rubber of GRC components can be used for further bonding.
安裝的質量標準：
Quality standards for installation:
1、構件安裝要求橫平豎直，整體在線，圖案完整，曲線光滑，構件表面沒有污染，無缺陷。
1. The components shall be installed horizontally and vertically, online as a whole, with complete patterns, smooth curves, and free of pollution and defects on the component surface.
2、正確找好構件的安裝節點，防止因預埋件錯位導致構件扭曲，長期產生安裝應力和變形。
2. Correctly locate the installation node of the component to prevent the component from twisting due to the dislocation of embedded parts, which will cause long-term installation stress and deformation.
3、構件連接點連接無泄漏，請擰緊螺栓后再擰緊。
3. There is no leakage at the connection points of components. Please tighten the bolts before tightening.
4、構件接縫光滑，接縫小于10毫米。
4. The joints of components shall be smooth and less than 10mm.
5、縱向構件請勿使上部構件與底部構件重疊，但是，各部件請單獨安裝在墻上。
5. Do not overlap the upper member and the bottom member of the longitudinal member, but install each component on the wall separately.
6、構件安裝后，需要自上而下將表面灰塵、污物清掃干凈，吊鉤間隙應牢固平整。
6. After the components are installed, the surface dust and dirt shall be cleaned from top to bottom, and the hook gap shall be firm and flat.
The above are the installation methods and installation quality standards introduced by GRC component manufacturers, which can resist damage, deformation and cracking of the external environment, and should be operated according to the correct installation methods. More precautions come to our website http://www.luxuryofwatches.cn consulting service
