GRC是一種以耐堿玻璃纖維為增強材料、水泥砂漿為基體材料的纖維混凝土復合材料，GRC是一種通過模具造型、紋理、質感與色彩表達設計師想象力的材料。那么廠家生產
濟南GRC構件過程中，監理單位和項目工程部應進行過程跟蹤檢查，確保廠家依合同、規范施工。其中制品材料應符合下列要求：
GRC is a kind of fiber concrete composite material with alkali-resistant glass fiber as the reinforcement material and cement mortar as the matrix material. GRC is a material that expresses the designer's imagination through mold modeling, texture, texture and color. During the production of Jinan GRC components by the manufacturer, the supervision unit and the project engineering department shall carry out process tracking inspection to ensure that the manufacturer works in accordance with the contract and specifications. The product materials shall meet the following requirements:
1.水泥：低堿度硫鋁酸鹽水泥；
1. Cement: low alkalinity sulphoaluminate cement;
2.集料：砂子含泥量不得大于1.0%，噴射工藝用砂的大粒徑應小于1.2mm，預混或鋪網抹漿工藝用砂的大粒徑應小于2.4mm，0.15mm以下顆粒的含量應小于10%；加強肋或填充空腔用混凝土中砂子的粒徑不受此限制；嚴禁使用海砂。
2. Aggregate: the silt content of sand shall not be greater than 1.0%, the large particle size of sand for spraying process shall be less than 1.2 mm, the large particle size of sand for pre-mixing or mesh plastering process shall be less than 2.4 mm, and the content of particles below 0.15 mm shall be less than 10%; The particle size of sand in the concrete for reinforcing ribs or filling cavities is not subject to this restriction; Sea sand is strictly prohibited.
3.GRC構件制品應按設計圖紙制造，其外觀尺寸應符合下表規定：
3. GRC component products shall be manufactured according to the design drawings, and their appearance dimensions shall comply with the following table:
4.構件的物理性能要求：
4. Physical performance requirements of components:
5.原材料出廠前后質量控制要點：
5. Key points of quality control of raw materials before and after delivery:
在制品明顯位置固定標明生產單位、商標、產品標記、生產日期以及“嚴禁碰撞”等字樣的標志。
Signs indicating the manufacturer, trademark, product mark, production date and the words "No Collision" shall be fixed at the obvious position of the products.
堆放：按規格型號分類堆放，堆放場地應平整、干燥、通風，堆放高度不應超過1.8米，堆放層數不應超過四層。
Stacking: The stacking shall be classified according to the specifications and models. The stacking site shall be flat, dry and ventilated. The stacking height shall not exceed 1.8m, and the number of stacking layers shall not exceed four.
裝卸、運輸：
Loading, unloading and transportation:
裝卸及搬運制品時，必須輕裝輕放，嚴禁拋擲。運輸時應固定牢靠，防止晃動，必要時在制品間用草墊隔開，制品不得超出車廂長度。
When loading, unloading and handling products, they must be handled with care and must not be thrown. During transportation, it shall be firmly fixed to prevent shaking. If necessary, the product room shall be separated by straw mats. The product shall not exceed the length of the carriage.
制品出廠應提交出廠證明書，其內容包括：
The ex-factory certificate shall be submitted when the product leaves the factory, and its contents include:
1）產品標記及數量；
1) Product marking and quantity;
2）出廠檢驗結果；
2) Delivery inspection results;
3）生產日期及出廠日期；
3) Production date and ex-factory date;
4）生產單位名稱及商標；
4) Name and trademark of the manufacturer;
5）生產單位質檢部門簽章。
5) Signature and seal of the quality inspection department of the production unit.
GRC is mainly used in the field of architecture, for building facade decoration and exterior wall decoration of indoor space, and also for building decoration components and landscape sketches. So, if you have any need for this, please come to our website to leave a message and contact us at any time http://www.luxuryofwatches.cn Do shopping!
