隨著grc構件的應用范圍越來越廣，在日常生活中隨處可見。而一個好的grc項目不僅需要生產出合格的grc產品，還需要良好的裝置技巧。這里分享一下grc構件裝置詳細的流程和注意事項。
With the wide application of GRC component, it can be seen everywhere in daily life. A good GRC project not only needs to produce qualified GRC products, but also needs good installation skills. Here we share the detailed process and precautions of GRC component device.
很多設計師認為建筑細節的處理可以直接反映一個設計師的設計水平。一個的建筑必須有的建筑細節，這些細節對加強特定的建筑設計效果起著決定性的作用。GRC構件的可塑性和耐用性等獨特優勢，了設計人員的后顧之憂。在很多情況下，GRC組件實際上是工藝產品。
Many designers believe that the treatment of architectural details can directly reflect a designer's design level. A perfect building must have perfect architectural details, which play a decisive role in strengthening the effect of specific architectural design. The unique advantages of GRC components, such as super plasticity and durability, perfectly solve the worries of designers. In many cases, GRC components are actually process products.
GRC建筑材料由于材料的特性，可以設計成多種風格。以輕燒氧化鎂、氯化鎂、硅、鈣等復合膠凝材料為主體，可制成GRC輕質隔墻板。同時墻板由生產線澆鑄、振動、壓實、整平、養護、脫模。
GRC building materials can be designed into a variety of styles due to the characteristics of materials. GRC light partition board can be made with light burned magnesium oxide, magnesium chloride, silicon, calcium and other composite cementitious materials as the main body. At the same time, the wallboard is cast, vibrated, compacted, leveled, maintained and demoulded by the production line.
GRC構件具有設計方便、周期短、重量輕等優點，可以設計成各種形狀和樣式。grc構件給大家增加了視覺效果，但是裝置grc構件并不是那么簡單。必須認真對待它的具體操作。
GRC components have the advantages of convenient design, short cycle and light weight, and can be designed into various shapes and styles. GRC component adds visual effect to everyone, but GRC component is not so simple. We must take its specific operation seriously.
基層的處理應認真對待，在構件裝置前應對建筑物的連接結構表面進行處理，確保平整、牢固。根據施工圖，在待裝置grc構件的位置彈出定位線裝置前應彈出水平、垂直和構件底座控制線。要求構件裝置誤差，單位裝飾面直線度誤差≤5mm/層高，總誤差≤30mm；裝置的連接應光滑，誤差超過3mm時應打磨。
The treatment of the base course shall be taken seriously. The surface of the connecting structure of the building shall be treated before the component installation to ensure flatness and firmness. According to the construction drawing, snap the positioning line at the position of the GRC component to be installed. Before the device, snap the horizontal, vertical and component base control lines. It is required that the component device error, the straightness error of unit decorative surface ≤ 5mm / floor height, and the total error ≤ 30mm; The connection of the device shall be smooth and polished when the error exceeds 3mm.
部件的連接應預留間隙，按規劃要求加工。有防水要求的部位應做好防水處理，并采取必要措施防止凍害。用建筑耐候密封膠將頂板與GRC構件墻體之間的縫隙填滿，構件與構件之間的縫隙停止沉降，然后用手指抹平壓實。
Clearance shall be reserved for the connection of components and processed according to the planning requirements. Waterproof treatment shall be carried out for parts with waterproof requirements, and necessary measures shall be taken to prevent freezing injury. Fill the gap between the top plate and GRC component wall with building weather resistant sealant, stop the settlement of the gap between components, and then smooth and compact with fingers.
所有預埋件裝置后應比外墻抹灰低15～20mm。外墻抹灰完畢后，抹灰層必須在裝置點開槽，不得外露預埋件。外墻保溫大于80mm時，構件的預埋件必須深入保溫板，離墻20mm，先打開保溫板，用膨脹螺栓固定，然后用聚苯乙烯泡沫塑料填充打開的孔。,外墻用外墻膩子修補，再外飾。
All embedded parts shall be 15 ~ 20mm lower than the external wall plastering after installation. After the plastering of the external wall, the plastering layer must be grooved at the device point, and the embedded parts shall not be exposed. When the external wall insulation is greater than 80mm, the embedded parts of the components must go deep into the insulation board 20mm away from the wall. First open the insulation board, fix it with expansion bolts, and then fill the open holes with polystyrene foam., The exterior wall shall be repaired with exterior wall putty and then decorated.
在潮濕的環境中，
濟南GRC構件施工時注意照明低于適用的電壓。構件的接縫小于10mm裝置完成后，要注意布置。
In the humid environment, the lighting shall be lower than the applicable safe voltage during the construction of GRC components in Jinan. The joint of components shall be less than 10mm. After the completion of the device, pay attention to the layout.
That's all about the GRC component devices. The details can also be handled according to the actual situation on site. Generally speaking, the devices are serious and must be treated strictly. For more content, please pay attention to our website www.luxuryofwatches.cn Com.
